Warm brick color that stays rich and easy to rinse
Brick Paver Sealing in Bunnell, FL
Call (386) 337-3172 to ask for a free brick paver sealing estimate in Bunnell.
- Brings out deeper paver color
- Fresh joint sand helps lock pavers in place
- Gives weeds less room to grow
- Makes the surface easier to keep clean
- Free estimate, no obligation
Request a Free Estimate
Free, no obligation.
Who seals brick pavers in Bunnell, and how quickly does a reply come?
A local contractor seals brick pavers throughout Bunnell, FL, and replies come within 1 business day, usually sooner. The estimate is free, and nothing obliges you to book once you hear the number. Ask any question you like about brick, sealer or timing. To begin, call (386) 337-3172.
Brick-colored pavers lose depth after a few summers of Florida sun. A wash, fresh joint sand and a low-sheen coat bring the warm tones back and make the walk easier to rinse. Picture the front steps and the path to the door looking even and clean when guests arrive. Tell the contractor which areas are brick, such as the walk, the patio or the drive, when you request your free estimate.
What counts as a brick paver at a Bunnell home?
The name covers two things. Some are fired clay bricks, and many are concrete pavers made in a brick color or pattern. Superior Brick Pavers says concrete fades over time from Florida's UV exposure, so color loss is a concrete issue as much as a brick one. The contractor should know which you have before choosing a sealer. To have yours identified, call (386) 337-3172.
Bunnell has brick in its history. Askflagler.com notes that the Bunnell First State Bank building went up in 1910 and joined the National Register of Historic Places in 1992. If your home or walkway uses older brick, say so when you request your free estimate.
Which Bunnell area towns can book a brick paver estimate?
Every town linked below has its own page, and the service area goes beyond them. Not sure about your street? Call (386) 337-3172.
What does brick paver sealing cost in Bunnell?
No page read for this guide gives a rate for brick pavers alone. A Volusia County paver company lists driveways at $1.50 to $2.50, pool decks at $1.75 to $3.00 and patios at $1.50 to $2.50, and for brick it uses its general range of $1.50 to $3.00. The table below applies that general range. For a number on your brick, request your free estimate.
What the sealer itself costs is small next to labor. Unilock lists sealer at $80 to $150 a gallon, covering 80 to 120 square feet for solvent and 100 to 150 for water-based. The rest of the bill is washing, drying and sand. Compare lines with a bid you already hold by calling (386) 337-3172.
| Brick area | Typical example | At $1.50 to $3.00 per sq ft |
|---|---|---|
| 150 sq ft | Front walk and entry | $225 to $450 |
| 400 sq ft | Back patio | $600 to $1,200 |
| 800 sq ft | Brick drive | $1,200 to $2,400 |
| 1,200 sq ft | Drive and walk together | $1,800 to $3,600 |
Built from the general paver range a Volusia County company published as of November 2026, because it lists no separate brick price. Stripping failed sealer or resetting loose bricks usually costs extra.
Should brick pavers be glossy or low sheen?
Low sheen is the safer look for brick. Unilock recommends matte or low gloss for brick pavers and warns that high gloss can be slippery when wet. Superior Brick Pavers says the finish should have a nice sheen and not look like glass. A wet-look coat deepens color more, but it asks more of a walk that gets rain. To see two finishes side by side, request your free estimate.
Alliance, a sealer maker, rates the natural look as adding about 5 percent to color and not slippery, with satin and wet looks changing color more. If you want your brick to look like itself, start there. Bring a photo of the color you want when you call (386) 337-3172.
Why do sealed brick pavers sometimes look hazy or milky?
It usually comes from too much sealer. Superior Brick Pavers says a sealer applied too often builds up and can turn into a milky white haze or begin to peel. Unilock says to apply in one go so layers do not pile on one spot, and to keep sprinklers off afterward because trapped water can cause white marks. Ask how many passes the contractor plans before you request your free estimate.
How often should Bunnell brick pavers be washed and resealed?
Superior Brick Pavers suggests washing one to two times a year and resealing no more often than every three to five years. It times the washes before fall, after the October leaf drop, and before spring pollen around Memorial Day. Unilock agrees on the three to five year reseal window. To plan your own schedule, call (386) 337-3172.
Do new brick pavers need to age before they are sealed?
Yes, a little. Unilock says efflorescence, the white salts that rise from new concrete pavers, can take 2 to 3 months to clear or up to a year, and that new pavers should wait 60 to 90 days. Sealing too early traps those salts under the coat as a cloudy patch. Mention how old your pavers are when you request your free estimate.
What stains show up on brick pavers around Bunnell?
Oak and pine litter leaves tannin marks, shade breeds green film and sprinkler heads can leave rust. UF/IFAS says iron runs high in most Florida well water, and rust deposits show up where it lands. Each stain gets its own cleaner, tried on a small spot first. Point to yours when you call (386) 337-3172.
What do sealed brick pavers look like in Bunnell?
How does the brick sealing process go?
The order matters more with brick than with plain gray pavers, because haze is harder to undo. To schedule a visit, call (386) 337-3172.
1. Identify what is under foot
The contractor checks whether the surface is a concrete paver in a brick color, a fired clay brick or something else, since cleaners and sealers are chosen to match.
2. Test a small corner
Unilock suggests trying the sealer on a small patch first. The patch shows the color change and the sheen before the whole walk is coated.
3. Wash and let it dry
Dirt and green film come off, then the pavers dry for at least a day. Moisture under a coat is how haze and white spots start.
4. Fill the joints
Joint sand goes in, and a sealer with a hardening agent can firm it up so rain does not carry it away.
5. One thin coat
A single, even pass goes on at the rate on the label. Extra layers stack up and can peel, so the job stops there.
Brick paver questions Bunnell homeowners ask
Is sealing brick pavers a good idea?
Usually, when the color has faded or the joints keep emptying. A coat deepens the color and makes dirt easier to rinse, and Superior Brick Pavers says its water-based sealer also firms up joint sand. The catch is that too much sealer builds up and can turn milky, so one thin coat on a clean, dry surface is the goal.
How much does it cost to have pavers cleaned and sealed?
Published Northeast Florida rates run $1.50 to $3.00 per square foot for the whole job. One Volusia County company lists no separate brick price and uses that general range. A 500 square foot brick patio would come to about $750 to $1,500.
How much does it cost to seal outdoor pavers?
Patios and walkways are listed at $1.50 to $2.50 per square foot by a Volusia County paver company, and pool decks at $1.75 to $3.00. Brick pavers follow the general range of $1.50 to $3.00. Size and condition move the price more than the paver style does.
How much does it cost to have your pavers sealed?
It depends on the area and the shape of the surface. Multiply your square footage by the published range of $1.50 to $3.00 to get a rough figure, then ask a contractor to confirm it on site. The sealer is a small part of that number, with the wash and sand taking most of the time.
What sheen should brick pavers have?
A low sheen. Unilock, a paver maker, recommends matte or low gloss for brick pavers, and Superior Brick Pavers says pavers should have a nice sheen and not a glass-like finish. A glossy coat on a front walk can feel slick when it rains.
How often should brick pavers be washed and resealed?
Superior Brick Pavers suggests washing one to two times a year and sealing no more often than every three to five years. Its timing for the wash is before fall, after the leaves come down in October, and before spring pollen around Memorial Day. A Bunnell yard with oaks follows the same calendar.
Why do brick pavers turn white or hazy after sealing?
Two common causes. Sealer applied too thick can leave a milky haze, as Superior Brick Pavers explains. Moisture trapped under the coat can also cloud it, which is one reason Unilock says to keep automatic sprinklers off after sealing.
Do new brick pavers have to wait before they are sealed?
Yes. Unilock says efflorescence can take 2 to 3 months or up to a year to finish, and that new pavers should wait 60 to 90 days. The white salts need to clear first, because sealer would trap them under the surface.
Want the brick looking warm and fresh again?
Reach out by phone or short form, and a reply arrives within 1 business day, usually much sooner.
Free, no obligation